Go to navigation links
Slip-resistant plywood in multiple surface patterns & colours

Slip-Resistant Plywood - Dark Grey Carat Pattern

This product is only sold in commercial quantity, e.g. full pallet per item - we cannot recommend any resellers

Dark Grey Carat pattern anti-slip plywood
  • Special order item - full pallets per item
  • 9mm-30mm
  • Maximum size 1880x4000mm
    (2900x13000mm if scarf jointed)
  • Typical pallet = approx. 2.8m3
    (e.g. 50 sheets 18mm 1250x2500mm)
  • Hazard Class EN 636-3 - suitable for fully exposed high-moisture conditions
  • Fire rating of EN 13501-1 Class Bfl-s1 (full pallets per item)

Surface pattern

Winwood Products is a supplier of the following Dark Grey Carat pattern slip-resistant plywoods:

Dark Grey Carat pattern plywood: Scan of anti-slip surface coating (approx. size = 135x90mm)

This slip-resistant, exterior plywood has a hard-wearing phenolic film overlay chemically bonded to its surface by heat and pressure. This surface layer is imprinted with a raised pattern consisting of thousands of dark grey diamond shapes, each approx. 10x4mm in size.

The small diamond pattern gives the panels a high degree of anti-slip properties and also reduces the bearing stress on the face veneer of the plywood, which improves its shear strength, allowing it to bear heavier point loads. The pattern not only gives the panels a surface that is skid resistant, but extremely easy to keep clean.

Information

Technical details (general)

  • Construction:
    • Exterior birch plywood faced with a slip-resistant, patterned phenolic resin coating that offers enhanced safety in the form of a resilient and water-proof anti-slip surface
  • Standard thickness:
    • 9mm, 12mm, 15mm, 18mm, 21mm, 24mm, 27mm, 30mm
      (plus surface coating)
  • Standard sizes:
    • 1200 / 1220 / 1250 x 2400 / 2440 / 2500mm
    • 1200 / 1220 x 3000 / 3050 / 3300 / 3600 / 4000mm
    • 1500 / 1525 / 1880 x 2400 / 2440 / 3000 / 3050 / 3600 / 4000mm
  • Special sizes:
    • In principle, any size can be produced up to the maximum stated above
      (or 2900x13000mm if scarf jointed)
  • Surface coating:
    • 220g/m2-440g/m2 dark grey patterned slip-resistant film
  • Edge treatment:
    • Typically sealed with exterior acrylic paint to protect against moisture
    • Notes:
      1. If the panels are subsequently cut to size, any newly exposed edges must be fully resealed using a suitable exterior protection system (e.g. acrylic paint)
      2. Rounding any sharp corners & edges will greatly help in the resealing process, as this will better allow the paint to fully adhere
      3. It is also highly recommended that after drilling holes or similar other areas where the water-resistant protective surface has been broken are sealed in a similar manner
  • Wear rating:
    • Taber abrasion value = 800R-1500R (EN 438-2), depending upon the coating
  • Tolerances:
    • Length/width: up to 1m @ ±1mm, up to 2m @ ±2mm , 2m & above @ ±3mm
    • Thickness: +0.2mm, -0.5mm
    • (Others by arrangement)
  • Specification:
    • EN 636-3 - Exterior & high moisture applications
  • Bonding Quality:
    • EN 314-2 Class 3 - Exterior
    • E1 (EN 13986) Low formaldehyde, CARB II, ULEF (Ultra Low Emitting Formaldehyde)